Home / Wardrobes / How to Build a Wardrobe

How to Build a Wardrobe

Building a wardrobe is a job of planning and patience rather than strength. Whether the wardrobe arrives as a flat pack or as boards cut to size, the work follows the same order: prepare the space, build the carcass square, fit the interior, then hang the doors. This guide walks through the steps, the tools you need, and the mistakes that cause most problems.

Summary Verdict

Building a wardrobe is a manageable job for two people with basic tools, as long as the carcass is built square and the floor is level. Rushing the first stage causes problems at every later stage.

Best for

Flat pack wardrobes built in the room where they will stand.

Anyone with basic tools and a free afternoon.

Watch out for

Building on an uneven floor, which throws the whole wardrobe out of square.

Skipping the wall fixing on a tall wardrobe.

Before you start

Start by clearing the space where the wardrobe will stand and the space where you will build it. A wardrobe carcass is large, and you need room to lay the panels flat and to turn the carcass upright when it is built. Measure the room, the ceiling height and the route the panels will travel, because a panel that does not fit through the door cannot be built in the room.

Check the floor with a spirit level. A floor that slopes will make the wardrobe lean, and the doors will not close squarely. If the floor is uneven, plan to level the wardrobe with adjustable feet or packers under the base. Open the box and check that every panel, fixing and fitting is present before you start, and read the instructions through once so you know the order of work.

Tools and fixings

The tools for a flat pack wardrobe are simple: a drill, a screwdriver, a spirit level, a tape measure and a rubber mallet. A second person is not a tool, but it helps more than any of them, because holding a large panel square while it is fixed is a two person job. Keep a pencil and a set square handy for marking, and a small step ladder for reaching the top of a tall wardrobe.

The fixings usually include cam locks, dowels and screws. Cam locks join the panels and pull them tight, dowels line the panels up, and screws hold the back panel and the fittings. Do not substitute your own screws unless you are sure of the length, because a screw that is too long will come through the face of a panel. Keep the fixings sorted as you go, so you are not hunting for a cam lock halfway through the build.

Building the carcass

The carcass is the box that forms the body of the wardrobe, and it must be built square. Start by joining the sides to the top and the base, working on a flat surface so the panels cannot twist. Use the dowels to line the panels up, then tighten the cam locks to pull the joints together. Check the corners with a set square as you go, because a joint that is out of square now will stay out of square.

The back panel is what makes the carcass rigid. Fit it squarely, with the corners of the carcass lined up, and fix it along all four edges. A back panel that is fitted crookedly will pull the whole carcass out of square, and the doors will never close properly. Once the back is on, stand the carcass upright and check it with a spirit level in both directions, then level it with the feet or packers.

Fitting the interior

With the carcass upright and level, fit the interior: the hanging rail, the shelves and any drawers. The rail should be fixed firmly at both ends with solid brackets, and it should sit level so that hangers do not slide to one end. Shelves should be fixed at the height you planned, with the supports seated fully in their holes, and drawers should be fitted on their runners and tested before the doors go on.

Think about the layout before you fix anything. A rail set too high wastes the space below it, and shelves set too far apart waste the space between them. Wardrobes with drawers need the drawer stack planned before the shelves are fixed, because the drawers take a fixed width of the carcass. It is easier to move a shelf now than to move it after the doors are hung.

Hanging the doors

Hinged doors are hung on the carcass with screws through the hinge plates. Fix the hinges to the door first, then offer the door up to the carcass and fix the hinge plates to the side panel. Work with the door held level, and fix one hinge at a time so the door cannot slip. Once both hinges are fixed, adjust them so the door sits square in the opening, with an even gap all round.

Sliding doors are fitted differently: the tracks are fixed to the top and bottom of the carcass, the rollers are fitted to the doors, and the doors are lifted into the tracks. Fitting sliding doors is a separate job with its own steps, and it needs the tracks to be level or the doors will drift. Whichever doors you have, test them several times and adjust the hinges or rollers until they open and close smoothly.

Fixing to the wall

A tall wardrobe must be fixed to the wall. A wardrobe that is 180 cm or taller can tip forward when a door is opened or a drawer is pulled out, and the weight of a falling wardrobe can cause a serious injury. The wall fixing is usually a strap or a bracket that screws to the top of the wardrobe and to the wall, and it should be fitted even if the wardrobe feels stable.

Find the right fixing for your wall. A solid wall takes a masonry plug and screw, while a plasterboard wall needs a plasterboard fixing or a screw into a stud. Do not rely on a fixing that is only in plaster, because it will pull out under load. If you are not sure what the wall is made of, check with a stud finder or a small pilot hole before you commit to a fixing.

Common mistakes

The most common mistake is building on an uneven floor without levelling the carcass. Everything that follows, the interior, the doors and the wall fixing, depends on the carcass being square and level, so a mistake at the start shows up at every later stage. The second mistake is tightening the fixings too hard, which can split a board or strip a cam lock, and the third is fitting the back panel crookedly, which pulls the carcass out of square.

Another common mistake is building the wardrobe in the wrong place. A wardrobe built in the middle of the room is hard to move once it is upright, so build it where it will stand, or as close as you can. Finally, do not skip the wall fixing, and do not leave the instructions unread. A wardrobe that is built well will last for years, and the hour spent getting the carcass square is the hour that makes the difference.

Build the carcass square and level, and everything after it is straightforward. Build it crooked, and every door, drawer and shelf will remind you of it.

Pros

  • A flat pack wardrobe can be built in the room where it stands
  • Basic tools and two people are enough for most builds
  • Building it yourself means you know how it is put together

Cons

  • An uneven floor throws the whole build out of square
  • Large panels need two people to handle safely
  • A mistake in the carcass shows up in every later stage