Home / Wardrobes / How to Fit Sliding Wardrobe Doors

How to Fit Sliding Wardrobe Doors

Fitting sliding wardrobe doors is a job of level tracks and careful adjustment. The doors themselves are simple panels, but they only run smoothly if the tracks are level, the rollers are set right, and the opening is measured accurately. This guide explains the steps in order, the tools you need, and how to fix a door that sticks or drifts.

Summary Verdict

Fitting sliding doors is a manageable job for two people with basic tools, as long as the opening is measured at several points and the tracks are fixed level. A track that is out of level will make the doors drift every time they are used.

Best for

Straight wardrobe openings where the doors can run on tracks.

Anyone comfortable with a drill and a spirit level.

Watch out for

Openings that are not square, which make the doors bind.

Heavy mirror doors that need two people to lift safely.

Measuring the opening

Measure the opening at the top, the middle and the bottom, and at the left and the right, because few openings are perfectly square. A wall that looks straight can vary by a centimetre from one end to the other, and a track cut to the widest measurement will not fit at the narrowest point. Take the smallest width measurement as the width to work to, and the smallest height as the height.

Check the opening with a spirit level as well. The top and the bottom should be level, and the sides should be upright. If the opening is out of level, the tracks will be too, and the doors will drift to the low side. Note the measurements down, and check them twice before you cut anything, because a track cut too short cannot be lengthened.

Tools and parts

The tools are simple: a drill, a screwdriver, a spirit level, a tape measure and a saw for cutting the tracks to length. A step ladder helps for reaching the top track, and a second person helps for holding the doors while they are lifted into the tracks. Keep a pencil handy for marking the track positions on the carcass or the wall.

The parts are the top track, the bottom track, the rollers, the door guides and the screws. The tracks are usually aluminium channels, cut to the width of the opening, and the rollers are small wheels fitted to the top and bottom of each door. Some kits include a soft close damper, which slows the door in the last few centimetres, and a floor guide that keeps the bottom of the door in line.

Fixing the tracks

Fix the bottom track first. Place it in the opening, check it with a spirit level, and mark the screw positions. If the floor of the opening is uneven, pack under the track with thin packers until it is level, because a track that slopes will make the doors drift. Drill pilot holes, then screw the track down firmly, and check the level again after the screws are tight.

Fix the top track next, directly above the bottom track, so the two tracks are in line. The top track carries the guide rollers and keeps the doors upright, so it must be level and firmly fixed. If the top of the opening is a ceiling or a fixed panel, use the fixings suited to that material, and check that the screws bite properly. A top track that works loose will let the doors lean and scrape.

Hanging the doors

Fit the rollers to the doors before you hang them, following the kit instructions for the position of each roller. The top rollers usually sit in the top track and guide the door, while the bottom rollers carry the weight in the bottom track. Check that each roller turns freely before you lift the door, because a stiff roller will make the door hard to move from the start.

Lift the door into place with two people, especially if it is a mirror door. Tilt the top of the door into the top track first, then lower the bottom rollers into the bottom track. The door should sit upright and move with a light push. If it leans or binds, lift it out and check that the rollers are seated properly in the tracks. How sliding doors work explains the mechanism in more detail, and it is worth reading before you start.

Adjusting the rollers

Most rollers can be adjusted up or down with a screw, and that adjustment is how you level the doors. If a door leans to one side, raise the roller on the low side until the door sits upright. If a door scrapes the track, lower the rollers until it clears. Work on one door at a time, and test it after each adjustment by sliding it the full length of the track.

Check the overlap between the doors as well. When both doors are closed, they should overlap by a few centimetres, so there is no gap into the wardrobe. If there is a gap, the doors are too narrow for the opening, and the only fix is wider doors. If the doors overlap too much, they will be hard to move past each other. Adjust the rollers until each door runs smoothly and the overlap is even.

Fixing common problems

A door that drifts to one side is usually a sign that the track is not level. Check the track with a spirit level and pack under the low side until it is level. A door that sticks is usually a sign of a dirty track or a worn roller, so clean the track with a brush and a damp cloth, and check the rollers for flat spots or damage. A door that jumps out of the track may have a roller that is not seated, or a track that is bent.

A door that rattles when it moves may have a loose roller or a guide that needs tightening. Check every screw on the rollers and the guides, and tighten any that have worked loose. If the door still rattles, the track may be the wrong size for the rollers, and the kit supplier should be asked. Most sliding door problems come back to the track or the rollers, and both are worth checking before you blame the door.

Finishing and safety

Once the doors run smoothly, fit any cover strips, handles and soft close dampers that came with the kit. The cover strips hide the tracks and give the wardrobe a finished look, and the handles make the doors easier to move, especially heavy mirror doors. Test the doors once more after the finishing touches are fitted, because a cover strip that is too tight can rub the door.

Finally, check the safety of the doors. Mirror doors should be safety backed, so the glass stays together if it breaks, and the doors should not be able to fall out of the tracks if they are pushed hard. Mirrored wardrobes need strong rollers and a firm track because of the weight, and a door that can be lifted out of the track too easily is a door that can fall. A sliding door that runs smoothly and stays in its track is a door that will last.

Fit the tracks level and the doors will look after themselves. Fit them out of level, and you will be adjusting the rollers for as long as the wardrobe stands.

Pros

  • Tracks and rollers can be fitted with basic tools
  • Rollers adjust, so doors can be levelled after fitting
  • Doors lift out of the tracks for cleaning and repair

Cons

  • A track out of level makes the doors drift
  • Heavy mirror doors need two people to lift safely
  • Openings that are not square make the doors bind