Teak garden furniture is famous for lasting outside, but it changes as it ages. Left alone, it weathers to a silver grey. Cleaned and oiled, it keeps its warm brown colour. Both are valid choices, and restoring teak is mostly a matter of cleaning and sanding, not of special products. This guide explains how to do it and how to decide.
Clean the teak, sand it lightly along the grain and oil it thinly if you want the brown colour back, or leave it to weather grey and just keep it clean.
Best for
Teak sets that have gone grey or green and are otherwise sound.
Anyone who wants the warm brown colour back without buying new furniture.
Watch out for
Sanding across the grain, which leaves marks that oil will highlight.
Oiling teak that is still damp, which traps moisture under the oil.
How teak ages
Teak is dense and naturally oily, which is why it resists rot and insects better than most garden woods. The oil sits in the grain and slows down the water that would otherwise get in. Over time, sun and rain wash the surface oil away, and the wood turns a silver grey. The grey is only a thin layer on the surface, and the wood underneath is still sound and still brown.
Teak also grows algae and collects dirt, especially in a damp garden. The algae sits on the surface and can be washed off, and the dirt sits in the grain and comes off with a brush. A teak set that looks grey and tired is usually just dirty and weathered, not worn out. The frame and the joints are what decide whether it is worth restoring, not the colour.
Assessing the condition
Before you start, check the whole piece. Press the joints and look for movement, check the feet and the end grain for splits, and look for black spots that could be rot. Teak rarely rots, but a joint that has been loose for years can let water in and soften the wood around it. If the frame is sound, the set is worth restoring. If a leg is split or a joint is broken, fix that first.
Tighten any loose bolts and screws, and replace any that are rusted. Teak is usually fixed with stainless steel, which does not rust, but older sets may have cheaper fixings. A chair that creaks will often go quiet once the fixings are tight. Take a photo of the set before you start, so you can see the change when you finish.
Cleaning the teak
Brush the set with a soft brush to get the loose dirt off, working along the grain. Then wash it with warm water and a mild soap, or a teak cleaner made for garden furniture, using a soft brush. Work along the grain, section by section, and rinse with clean water as you go. Green algae usually comes off with gentle scrubbing, and a little white vinegar in the water helps with stubborn patches.
Do not use a pressure washer on teak. The jet lifts the grain and leaves a rough surface that will need heavy sanding to fix. Do not use bleach either, because it dries the wood and fades it unevenly. The guide to cleaning wooden garden furniture covers the same washing method for other woods, and the rules are the same: gentle, along the grain, and rinse well.
| Step | What to do | What to avoid |
|---|---|---|
| Clean | Brush, wash with mild soap | Pressure washer, bleach |
| Dry | Air dry for a day or more | Heaters, strong direct sun |
| Sand | Fine sandpaper, along grain | Coarse paper, across grain |
| Oil | Thin coat, wipe excess | Thick coats, oiling damp wood |
| Leave grey | Wash and dry only | Oiling over dirt or algae |
Sanding the surface
Once the teak is clean and dry, sand it lightly with a fine sandpaper, working along the grain. The aim is to take the grey layer off and smooth the surface, not to cut deep into the wood. The brown colour will show through as you sand, and that tells you the grey is gone. Sand the flat surfaces first, then the edges and the slats, and keep the pressure even.
Wipe the dust off with a damp cloth and let the wood dry again. Run a hand over the surface: if it feels smooth, the sanding is done. If it feels rough in places, sand those spots again lightly. Do not sand across the grain, because the marks will show once the oil goes on. A light, even sanding is all a sound teak set needs.
The grey is only a thin layer on the surface, and the wood underneath is still sound and still brown.
Oiling or leaving it grey
If you want the brown colour, oil the teak once it is dry. Use an oil made for teak, apply it thinly with a cloth or a brush along the grain, and wipe off the excess after the time stated on the tin. One thin coat is enough to start with, and a second coat can go on the next day. The oil soaks into the grain and brings the colour back, and it slows the weathering for a season.
If you prefer the grey, do nothing more than keep the set clean. The grey is a natural weathered finish, and many people prefer it. Oiling is not required to keep teak sound, and a grey set will last just as long as an oiled one. The choice is about looks, not about durability, so pick the finish you like and stick with it.
Joints, fixings and ongoing care
While the set is clean and dry, check the joints once more. Tighten the fixings, and replace any that are worn. A drop of oil on a stiff bolt will help it turn, and a wooden joint that is loose can be glued and clamped, but that is a bigger job. Check the feet too, because teak feet can wear down on stone and let water sit against the end grain.
Ongoing care is simple. Wash the set in spring and autumn, oil it once a year if you want the brown colour, and cover it or store it under cover over winter. A teak set looked after this way can last for decades, and it will still be sound long after cheaper sets have been replaced. The work is an afternoon a year, and the set repays it every summer.