IKEA furniture arrives flat-packed, in a box of panels, fixings and pictorial instructions, and most pieces are built at home. The process is straightforward when it is done in order, and it goes wrong when steps are skipped. This guide explains how assembly works, what tools you need, and what to check as you build.
Assembly goes well when you work in order, check the parts first and build on a clear floor. The instructions are pictorial, so follow the pictures, not your guess at what comes next.
Best for
Anyone building a first piece of flat-pack furniture.
Shoppers who want to know what the job involves before they buy.
Watch out for
Skipping a step or forcing a joint can damage the panels.
Large pieces need two people and a clear floor.
What is in the box
A flat-pack box contains the panels, the fixings and the instructions. The panels are usually chipboard or fibreboard, with a laminate or veneer surface, and they are cut to size and drilled with holes for the fixings. The fixings include dowels, screws, cam locks and brackets, and they are usually in a small bag or a set of bags. The instructions are pictorial, with no words, and they show each step in order.
Before you start, open the box and check that all the parts are there. Count the panels against the parts list in the instructions, and check the fixings bag. A missing panel or a missing bag of fixings is easier to sort out before you start than halfway through the build, when the piece is half assembled and cannot be moved.
Tools you need
Most IKEA furniture needs only a screwdriver and an Allen key, which is included in the box. A drill can speed the work up, especially for a large piece with many screws, but it should be used on a low setting, because a drill on full power can strip the screws or split the panels.
A hammer is sometimes useful for tapping dowels into place, and a tape measure is useful for checking that the piece is square. A spirit level is worth having for a wardrobe or a shelving unit, because a piece that is not level will lean and the doors will not close properly. Keep the tools to hand before you start, because stopping to look for a screwdriver halfway through is a good way to lose a fixing.
Reading the instructions
The instructions are pictorial, and they show each step as a drawing. The steps are numbered, and they must be followed in order, because a step that is skipped can make a later step impossible. The drawings show which panel goes where, which fixing is used, and which way round the panel goes. Pay attention to the small details, such as the direction of a dowel or the position of a cam lock, because they matter.
The instructions also show warnings, such as a picture of a person with a cross through it, which means the step needs two people, or a picture of a wall fixing, which means the piece must be fixed to the wall. Read the whole set of instructions before you start, so you know what the job involves and how long it will take. A quick read through saves time later.
Building in order
Build on a clear floor, with enough space to lay the panels out. Start by laying the panels in order, and check that you can tell them apart, because many panels look similar and the holes are in different places. Work through the instructions step by step, and do not tighten the fixings fully until the piece is assembled, because a fixing tightened too early can pull the panels out of square.
The back panel is important: it gives the piece its rigidity, and a piece without a properly fitted back will rack, or lean out of square. Fit the back carefully, and check that the piece is square before you stand it up. Measure the diagonals: if they are equal, the piece is square. If they are not, loosen the fixings, square the piece, and tighten them again.
Flat-pack assembly is a sequence, not a puzzle. Follow the pictures in order, and the piece will come together. Skip a step, and it will not.
Common mistakes
The most common mistake is forcing a joint. If a dowel or a screw does not go in, stop and check: the panel may be the wrong way round, the hole may be in the wrong place, or the fixing may be the wrong one. Forcing it will split the panel or strip the hole, and a split panel cannot be fixed easily. Take the joint apart, check the instructions, and try again.
Another common mistake is building the piece in the wrong room, or building it where it cannot be moved. A wardrobe built flat on the floor must be tilted upright, so the ceiling must be high enough, and the room must be clear. A chest of drawers built in a hallway may not fit through the door to the bedroom. Build the piece in the room where it will live, if you can, or check that it will fit through the doors when it is built.
Fixing to the wall
Tall pieces, such as wardrobes, chests of drawers and shelving units, must be fixed to the wall. The fixings are included, but the wall plugs depend on the wall type, and a plasterboard wall needs different fixings from a brick wall. A piece that is not fixed to the wall can tip forward, especially when the doors are open and the drawers are pulled out, so the fixing is not optional.
Check the wall before you drill, and check for pipes and cables. Use a detector if you are unsure, and use the right plugs for the wall. If the wall is plasterboard and you are not confident, ask a professional, because a piece fixed to a plasterboard wall with the wrong fixings is no safer than one that is not fixed at all. Our guide to PAX wardrobes explains the wall fixing for the largest IKEA pieces.
Pros
- Flat-pack is cheaper to transport and to store
- Pictorial instructions need no language
- Most pieces need only a screwdriver and an Allen key
Cons
- Large pieces take hours and need two people
- A skipped step can make a later step impossible
- Forcing a joint can split a panel
The assembly service
IKEA offers an assembly service for those who do not want to build the furniture themselves. The service is booked at the point of sale or online, and a professional team will build the furniture at your home. The service is worth considering for large pieces, such as wardrobes and kitchens, because a piece built by a professional will be square and level, while a piece built in a hurry may not be.
The assembly service is separate from delivery, and it is charged separately. Check what it includes, and whether it includes fixing the piece to the wall, because that is a separate step. If you book the service, clear the room before the team arrives, and make sure the boxes are in the room where the piece will live.
After the build
Once the piece is built, check it. Open and close the doors and the drawers, and check that they run smoothly and close fully. Check that the piece is level, and that it does not rock on the floor. Tighten the fixings after a week of use, because they can settle, and a fixing that has loosened will let the piece wobble.
Keep the instructions and the spare fixings, because they are useful if the piece needs to be taken apart or repaired. Keep the receipt too, because a piece that has been assembled is harder to return than one still in its flat-pack box, and the returns terms depend on the condition. A piece that is built well and checked properly will last for years.