Home / Dining chairs / Dining Chair Height: What to Know

Dining Chair Height: What to Know

Dining chair height is the measurement that decides whether a chair is comfortable at a table. A chair that is too high will leave no room for the thighs, and a chair that is too low will leave the sitter reaching up to the table. This guide explains the standard heights, the gap that matters, how to measure, and what to do when a chair does not fit.

Summary Verdict

Chair height is about the gap between the seat and the table, not the height of the chair alone. A seat about 45 cm high with a table about 75 cm high gives the gap that most people find comfortable.

Best for

Anyone buying chairs for a table they already own.

Households where the chairs and the table were bought separately.

Watch out for

Chairs that are too high, leaving no room for thighs.

Chairs with arms that do not fit under the table.

Why 45 cm is the standard

A dining chair seat is about 45 cm high because that height suits the average adult leg. When a person sits on a chair 45 cm high, the thighs are roughly level, the feet rest flat on the floor, and the knees bend at about a right angle. That is the posture that is comfortable for eating, because the body is supported and the arms rest naturally on the table.

The height is a standard, not a rule, and it suits most adults, although taller and shorter people may prefer a seat a few centimetres higher or lower. A chair that is 43 cm high will suit a shorter person, and a chair that is 48 cm high will suit a taller one, but a chair that is far from 45 cm will be uncomfortable for most people. The standard exists because it works for the most people, most of the time.

The gap that matters

The measurement that matters most is not the seat height or the table height alone, but the gap between them. The gap is measured from the top of the seat to the underside of the table, and it should be about 25 to 30 cm. That gap is what lets a person sit with thighs under the table, and it is what decides whether the chair is comfortable, however tall the chair and the table are on their own.

A gap smaller than 25 cm will leave no room for the thighs, and the sitter will have to sit back from the table or sit with the legs to one side. A gap larger than 30 cm will leave the sitter reaching up to the table, with the arms raised and the shoulders tense. Both are uncomfortable, and both are caused by a chair and a table that do not match, even if each is the right height on its own.

How to measure

Measure the seat height from the floor to the top of the seat, at the front edge where the sitter sits. If the seat is padded, press the padding down as you measure, because the padding compresses when a person sits on it, and the height that matters is the height under weight. Measure the table height from the floor to the top of the table, and measure the thickness of the top, because the gap is measured to the underside, not to the top.

Subtract the seat height from the table height, then subtract the thickness of the tabletop, and the result is the gap. If the gap is between 25 and 30 cm, the chair and the table match. If it is not, the chair or the table needs to change. Dining chairs in general are about 45 cm high, and dining tables in general are about 75 cm high, so a standard chair and a standard table will usually match.

Chairs with arms

A chair with arms adds another measurement: the height of the arms. The arms should fit under the table, so the chair can be pushed in, and they should be at a height that supports the elbows without raising the shoulders. The arms are usually about 20 cm above the seat, which puts them about 65 cm from the floor, and the underside of the table is about 72 cm from the floor, so the arms should clear it.

Check the arm height by pushing the chair under the table. If the arms hit the table, the chair cannot be pushed in fully, and it will stick out into the room. Some chairs with arms are made with lower arms to fit under a table, and some tables are made with a thinner top to give more clearance. The arms should also be at a height that suits the sitter: arms that are too high will raise the shoulders, and arms that are too low will not support the elbows.

Counter height and bar stools

Counter height chairs and bar stools are taller than dining chairs, and they suit a kitchen island or a breakfast bar, not a dining table. A counter chair has a seat about 60 cm high, to match a counter about 90 cm high, and a bar stool has a seat about 75 cm high, to match a bar about 105 cm high. The gap between the seat and the counter follows the same rule, about 25 to 30 cm.

Do not use a counter chair at a dining table, because the seat will be too high and the gap will be too small. Do not use a dining chair at a counter, because the seat will be too low and the gap will be too large. The heights are set for the surface they go with, and a chair that is the wrong height for the surface will be uncomfortable, however well it is made.

When a chair does not fit

A chair that is too high for the table can sometimes be fixed by removing a seat pad, if the chair has one, or by choosing a thinner pad. A chair that is too low can sometimes be fixed by adding a seat pad, which raises the seat by a few centimetres. Both are small adjustments, and they work when the difference is a few centimetres, not when it is much more.

A chair that is far too high or too low for the table cannot be fixed, and the chair or the table needs to change. A table that is too high for its chairs can sometimes be lowered by shortening the legs, although that is a job for a workshop, and a table that is too low cannot easily be raised. The simplest answer is to buy the chair and the table together, or to measure both before you buy, so the gap is right from the start.

What to check before you buy

Sit on the chair at the table before you buy it, if you can. Check that your knees clear the underside of the table, that your thighs fit in the gap, and that your arms rest comfortably on the table. Check that the chair can be pushed in, and that the arms, if it has them, fit under the table. Measure the seat height and the table height, and work out the gap.

Check the height of the chair back as well. The back should support the lower back, and the top rail should be at a height that suits the shoulders. Choosing dining chairs covers the other checks to make, and the height is the first of them, because a chair that is the wrong height will never be comfortable, however well it is made.

Chair height is about the gap, not the chair. Measure the gap between the seat and the table, and the comfort follows from that number.
SurfaceSurface heightSeat heightGap
Dining tableAbout 75 cmAbout 45 cmAbout 25 to 30 cm
Kitchen counterAbout 90 cmAbout 60 cmAbout 25 to 30 cm
BarAbout 105 cmAbout 75 cmAbout 25 to 30 cm