Most IKEA furniture is made from chipboard with a laminate surface, and paint does not stick to laminate on its own. It needs sanding and priming first, and the preparation matters more than the painting. This guide explains the steps in general terms, from cleaning and sanding to priming and painting.
Painting IKEA furniture works well when the surface is prepared properly. Skip the sanding and priming, and the paint will peel. Take time over the preparation, and the finish will last.
Best for
Anyone who wants to change the colour of a piece they already own.
Small pieces, such as a chest of drawers or a bedside table.
Watch out for
Laminate is smooth, so paint peels off if it is not sanded and primed.
Painting a piece you may return is not advisable.
Why laminate needs preparation
Laminate is a smooth, hard surface, made to resist stains and wear. That smoothness is the problem for paint: there is nothing for the paint to grip, so it sits on the surface and peels off when it is knocked or scratched. Sanding roughs the surface up, giving the paint something to hold onto, and priming gives the paint a layer to bond to.
Solid wood is different. It has a grain that paint can grip, and it can be sanded back and repainted if the finish fails. Laminate cannot be sanded back in the same way, because sanding through the laminate exposes the chipboard underneath, which swells when it gets wet. The panels are joined with dowels and cam locks, the same fixings used across IKEA flat-pack furniture, so the joints deserve the same care as the surface when you prepare a piece.
Cleaning first
Before any sanding, clean the piece thoroughly. Dust, grease and polish all stop paint sticking, and they are easy to miss on a surface that looks clean. Wipe the piece with a cloth and a mild detergent, then wipe it again with clean water, and let it dry fully. Pay attention to the handles and the edges, where grease and dirt collect.
Remove the handles, knobs and any hardware before you start, and put the screws in a bag so they do not get lost. If the piece has drawers, take them out and paint them separately, because it is easier to reach the edges and the insides. Work in a ventilated room, and cover the floor, because sanding and painting make a mess.
Sanding the surface
Sand the surface lightly with a fine sandpaper, enough to take the shine off the laminate and leave a dull, rough surface. You do not need to sand through the laminate, only to rough it up. Work in the direction of the grain if there is one, and sand the edges and the corners as well, because paint peels first at the edges.
After sanding, wipe the piece with a damp cloth to remove the dust, then let it dry. Dust left on the surface will show through the paint as a rough finish, so take time over this step. If the piece has any damage, such as a chip in the laminate, fill it with a wood filler, let it dry, and sand it smooth before you prime.
Priming
Primer is the layer between the laminate and the paint, and it is the step that makes the difference. A primer made for laminate or for difficult surfaces will bond to the smooth surface and give the paint something to grip. Apply it in a thin, even coat, with a brush or a roller, and let it dry fully before you paint. The primer does not need to look perfect, but it needs to cover the surface evenly.
Some paints claim to need no primer, but on laminate a primer is still the safer choice. A coat of primer takes little time, and it is far easier than stripping paint that has peeled. Check that the primer suits the paint you will use, because a primer and a paint that do not work together can cause the paint to lift.
Paint does not stick to laminate on its own. Sanding gives it something to grip, and priming gives it something to bond to.
Painting
Paint in thin, even coats, with a brush or a roller, and let each coat dry fully before the next. Two thin coats are better than one thick coat, because a thick coat takes longer to dry, it can drip, and it is more likely to peel. Work in a ventilated room, and keep the piece dust free while it dries, because dust in wet paint leaves a rough finish.
Use a paint suited to furniture, and check that it suits the primer you have used. A furniture paint is harder wearing than a wall paint, and it will stand up better to knocks and cleaning. A roller gives a smooth finish on flat surfaces, while a brush is better for edges, corners and detailed parts. Take your time, because a rushed coat shows in the finish.
Finishing and sealing
Once the paint is dry, the piece may need a clear topcoat or a sealant, especially if it will be used every day. A topcoat protects the paint from knocks, scratches and cleaning, and it gives the finish a harder surface. Check whether the paint you have used needs a topcoat, and whether the topcoat suits the paint.
Let the piece dry fully before you put the handles back on and use it. Paint can feel dry to the touch while it is still soft underneath, and using the piece too soon can mark the finish. Allow the drying time stated on the paint, and longer if the room is cold or damp. A piece that is left to cure properly will last far longer than one that is used too soon.
Pros
- Changes the look of a piece without replacing it
- Cheap compared with buying new furniture
- Works well on small pieces with good preparation
Cons
- Needs sanding and priming, or the paint will peel
- Takes time, with drying between coats
- Cannot be sanded back like solid wood
What not to paint
Do not paint a piece you may want to return, because a painted piece cannot be returned. Do not paint a piece that is still under guarantee if the painting would void it, and check the terms before you start. Do not paint the inside of a drawer or a wardrobe if the paint will stick to the clothes inside, and do not paint a surface that will be in contact with food unless the paint is suited to it.
Do not skip the preparation. The temptation is to paint straight onto the laminate, because it looks clean and smooth, but the paint will peel within weeks. Sanding and priming take time, but they are the steps that make the finish last. A piece that is painted properly will look good for years, and a piece that is painted in a hurry will need doing again.
A simple order to follow
Clean the piece, remove the hardware, and sand the surface lightly. Wipe off the dust, fill any damage, and let it dry. Prime in a thin, even coat, and let it dry fully. Paint in two thin coats, letting each one dry, and add a topcoat if the paint needs one. Let the piece cure fully before you put the handles back on and use it.
That order is the whole job. The painting itself is the easy part, and the preparation is the part that decides whether the finish lasts. Take time over the preparation, and the piece will look as if it was made in the colour you chose, rather than painted over.